This allows 3160 / 7260 / 7265 / 7265D / 8000 devices to
use the latest version of the firmware.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Use only basic dwell time (10 ms for active scan and 110 for passive),
regardless of the number of the probes and the band, if it is
supported by the FW. The FW will add 3 ms for each probe sent and 10
ms for low band channels.
Add a TLV flag to indicate such support in FW.

This fix is needed to fix few bugs regarding scans that take too much time.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Add a flag that enables match found notification to align with
FW API change.

Cc: <stable@vger.kernel.org> [3.17+]
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When tid_tspec was set to IWL_TID_NON_QOS (8) this led to an
out of bounds access to the tid_to_mac80211_ac array whose size
is 7. Fix this.

Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

commit 5c904224
"iwlwifi: mvm: don't allow diversity if BT Coex / TT forbid it"
broke Rx with 2 chains for diversity.
This had an impact on throughput where we're using only a single
stream (11a/b/g APs, single stream APs, static SMPS).

Fixes: 5c904224

 ("iwlwifi: mvm: don't allow diversity if BT Coex / TT forbid it")
Cc: Stable <stable@vger.kernel.org>  [3.16+]
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

We were advertising iwlwifi-7265-X.ucode instead of
iwlwifi-7265D-X.ucode. Fix this.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The trans cfg was not replaced for 7265-D cards. This led to a check of
the min-NVM version against a 7265-C card, causing very-old 7265-D cards
to operate incorrectly with the driver.

Fixes: 3fd0d3c1

 ("iwlwifi: pcie: support 7265-D devices")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

New FW has chunks that are larger than the size limit of the
FH's DMA. To make sure we don't crash it - actively limit the
max size of each chunk.

Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

A few device IDs were added, reflect this change in the
driver.

Cc; <stable@vger.kernel.org> [3.13+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In the very unlikely case in which no firmware could be,
found. the same pointer was freed twice. Fix that.

Fixes: 490fefeb

 ("iwlwifi: define the .ucode file format for debug")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When we reset the device, the CSR_INT gets cleared as well
as CSR_INT_MASK. Meaning that we shouldn't get any interrupt
but, due to a hardware bug, recent devices will keep sending
interrupts. This leads to an interrupt storm while stopping
the device.
The way to fix this is to ACK all the interrupts after the
device is reset so that the value of CSR_INT will stay
0xffffffff.

Fixes: 522713c8

 ("iwlwifi: pcie: properly reset the device")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

On stop(), we already cleared our internal state,
and the restart_complete() callback won't be
called, so simply clear the IN_HW_RESTART flag.

Keeping the flag might result in invalid state
on the next start(), preventing the driver starting
properly.

Additionally, don't take IWL_MVM_REF_UCODE_DOWN on stop()
if hw restart was requested, as the ref was already
taken in this case.

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Pull networking updates from David Miller:

 1) New offloading infrastructure and example 'rocker' driver for
    offloading of switching and routing to hardware.

    This work was done by a large group of dedicated individuals, not
    limited to: Scott Feldman, Jiri Pirko, Thomas Graf, John Fastabend,
    Jamal Hadi Salim, Andy Gospodarek, Florian Fainelli, Roopa Prabhu

 2) Start making the networking operate on IOV iterators instead of
    modifying iov objects in-situ during transfers.  Thanks to Al Viro
    and Herbert Xu.

 3) A set of new netlink interfaces for the TIPC stack, from Richard
    Alpe.

 4) Remove unnecessary looping during ipv6 routing lookups, from Martin
    KaFai Lau.

 5) Add PAUSE frame generation support to gianfar driver, from Matei
    Pavaluca.

 6) Allow for larger reordering levels in TCP, which are easily
    achievable in the real world right now, from Eric Dumazet.

 7) Add a variable of napi_schedule that doesn't need to disable cpu
    interrupts, from Eric Dumazet.

 8) Use a doubly linked list to optimize neigh_parms_release(), from
    Nicolas Dichtel.

 9) Various enhancements to the kernel BPF verifier, and allow eBPF
    programs to actually be attached to sockets.  From Alexei
    Starovoitov.

10) Support TSO/LSO in sunvnet driver, from David L Stevens.

11) Allow controlling ECN usage via routing metrics, from Florian
    Westphal.

12) Remote checksum offload, from Tom Herbert.

13) Add split-header receive, BQL, and xmit_more support to amd-xgbe
    driver, from Thomas Lendacky.

14) Add MPLS support to openvswitch, from Simon Horman.

15) Support wildcard tunnel endpoints in ipv6 tunnels, from Steffen
    Klassert.

16) Do gro flushes on a per-device basis using a timer, from Eric
    Dumazet.  This tries to resolve the conflicting goals between the
    desired handling of bulk vs.  RPC-like traffic.

17) Allow userspace to ask for the CPU upon what a packet was
    received/steered, via SO_INCOMING_CPU.  From Eric Dumazet.

18) Limit GSO packets to half the current congestion window, from Eric
    Dumazet.

19) Add a generic helper so that all drivers set their RSS keys in a
    consistent way, from Eric Dumazet.

20) Add xmit_more support to enic driver, from Govindarajulu
    Varadarajan.

21) Add VLAN packet scheduler action, from Jiri Pirko.

22) Support configurable RSS hash functions via ethtool, from Eyal
    Perry.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1820 commits)
  Fix race condition between vxlan_sock_add and vxlan_sock_release
  net/macb: fix compilation warning for print_hex_dump() called with skb->mac_header
  net/mlx4: Add support for A0 steering
  net/mlx4: Refactor QUERY_PORT
  net/mlx4_core: Add explicit error message when rule doesn't meet configuration
  net/mlx4: Add A0 hybrid steering
  net/mlx4: Add mlx4_bitmap zone allocator
  net/mlx4: Add a check if there are too many reserved QPs
  net/mlx4: Change QP allocation scheme
  net/mlx4_core: Use tasklet for user-space CQ completion events
  net/mlx4_core: Mask out host side virtualization features for guests
  net/mlx4_en: Set csum level for encapsulated packets
  be2net: Export tunnel offloads only when a VxLAN tunnel is created
  gianfar: Fix dma check map error when DMA_API_DEBUG is enabled
  cxgb4/csiostor: Don't use MASTER_MUST for fw_hello call
  net: fec: only enable mdio interrupt before phy device link up
  net: fec: clear all interrupt events to support i.MX6SX
  net: fec: reset fep link status in suspend function
  net: sock: fix access via invalid file descriptor
  net: introduce helper macro for_each_cmsghdr
  ...

Pull sound updates from Takashi Iwai:
 "This became a fairly large pull request.  In addition to the usual
  driver updates / fixes, there have been a high amount of cleanups in
  ASoC area, as well as control API helpers and kernel documentations
  fixes touching through the whole tree.

  In the driver side, the biggest changes are the support for new Intel
  SoC found on new x86 machines, and the updates of FireWire dice and
  oxfw drivers.

  Some remarkable items are below:

  ALSA core:
   - PCM mmap code cleanup, removal of arch-dependent codes
   - PCM xrun injection support
   - PCM hwptr tracepoint support
   - Refactoring of snd_pcm_action(), simplification of PCM locking
   - Robustified sequecner auto-load functionality
   - New control API helpers and lots of cleanups along with them
   - Lots of kerneldoc fixes and cleanups

  USB-audio:
   - The mixer resume code was largely rewritten, and the devices with
     quirks are resumed properly.
   - New hardware support: Focusrite Scarlett, Digidesign Mbox1,
     Denon/Marantz DACs, Zoom R16/24

  FireWire:
   - DICE driver updates with better duplex and sync support, including
     MIDI support
   - New OXFW driver for Oxford Semiconductor FW970/971 chipset,
     including the previous LaCie Speakers device.  Fullduplex and MIDI
     support included as well as DICE driver.

  HD-audio:
   - Refactoring the driver-caps quirk handling in snd-hda-intel
   - More consistent control names representing the topology better
   - Fixups: HP mute LED with ALC268 codec, Ideapad S210 built-in mic
     fix, ASUS Z99He laptop EAPD

  ASoC:
   - Conversion of AC'97 drivers to use regmap, bringing us closer to
     the removal of the ASoC level I/O code
   - Clean up a lot of old drivers that were open coding things that
     have subsequently been implemented in the core
   - Some DAPM performance improvements
   - Removal of the now seldom used CODEC mutex
   - Lots of updates for the newer Intel SoC support, including support
     for the DSP and some Cherrytrail and Braswell machine drivers
   - Support for Samsung boards using rt5631 as the CODEC
   - Removal of the obsolete AFEB9260 machine driver
   - Driver support for the TI TS3A227E headset driver used in some
     Chrombeooks

  Others:
   - ASIHPI driver update and cleanups
   - Lots of dev_*() printk conversions
   - Lots of trivial cleanups for the codes spotted by Coccinelle"

* tag 'sound-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (594 commits)
  ALSA: pcxhr: NULL dereference on probe failure
  ALSA: lola: NULL dereference on probe failure
  ALSA: hda - Add "eapd" model string for AD1986A codec
  ALSA: hda - Add EAPD fixup for ASUS Z99He laptop
  ALSA: oxfw: Add hwdep interface
  ALSA: oxfw: Add support for capture/playback MIDI messages
  ALSA: oxfw: add support for capturing PCM samples
  ALSA: oxfw: Add support AMDTP in-stream
  ALSA: oxfw: Add support for Behringer/Mackie devices
  ALSA: oxfw: Change the way to start stream
  ALSA: oxfw: Add proc interface for debugging purpose
  ALSA: oxfw: Change the way to make PCM rules/constraints
  ALSA: oxfw: Add support for AV/C stream format command to get/set supported stream formation
  ALSA: oxfw: Change the way to name card
  ALSA: dice: Add support for MIDI capture/playback
  ALSA: dice: Add support for capturing PCM samples
  ALSA: dice: Support for non SYT-Match sampling clock source mode
  ALSA: dice: Add support for duplex streams with synchronization
  ALSA: dice: Change the way to start stream
  ALSA: jack: Add dummy snd_jack_set_key() definition
  ...

Pull devicetree changes from Grant Likely:
 "Lots of activity in the devicetree code for v3.18.  Most of it is
  related to getting all of the overlay support code in place, but there
  are other important things in there.

  Highlights:

   - OF_RECONFIG notifiers for SPI, I2C and Platform devices.  Those
     subsystems can now respond to live changes to the device tree.

   - CONFIG_OF_OVERLAY method for applying live changes to the device
     tree

   - Removal of the of_allnodes list.  This used to be used to iterate
     over all the nodes in the device tree, but it is unnecessary
     because the same thing can be done by iterating over the list of
     child pointers.  Getting rid of of_allnodes saves some memory and
     avoids the possibility of of_allnodes being sorted differently from
     the child lists.

   - Support for retrieving original DTB blob via sysfs.  Needed by
     kexec.

   - More unittests

   - Documentation and minor bug fixes"

* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux: (42 commits)
  of: Delete unnecessary check before calling "of_node_put()"
  of: Drop ->next pointer from struct device_node
  spi: Check for spi_of_notifier when CONFIG_OF_DYNAMIC=y
  of: support passing console options with stdout-path
  of: add optional options parameter to of_find_node_by_path()
  of: Add bindings for chosen node, stdout-path
  of: Remove unneeded and incorrect MODULE_DEVICE_TABLE
  ARM: dt: fix up PL011 device tree bindings
  of: base, fix of_property_read_string_helper kernel-doc
  of: remove select of non-existant OF_DEVICE config symbol
  spi/of: Add OF notifier handler
  spi/of: Create new device registration method and accessors
  i2c/of: Add OF_RECONFIG notifier handler
  i2c/of: Factor out Devicetree registration code
  of/overlay: Add overlay unittests
  of/overlay: Introduce DT overlay support
  of/reconfig: Add OF_DYNAMIC notifier for platform_bus_type
  of/reconfig: Always use the same structure for notifiers
  of/reconfig: Add debug output for OF_RECONFIG notifiers
  of/reconfig: Add empty stubs for the of_reconfig methods
  ...

Pull fbdev updates from Tomi Valkeinen:
 - support for mx6sl and mx6sx
 - OMAP HDMI audio rewrite to make it finally work
 - OMAP video PLL work to prepare for new DRA7xx SoCs
 - simplefb DT related improvements

* tag 'fbdev-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (81 commits)
  video: uvesafb: Deletion of an unnecessary check before the function call "platform_device_put"
  video: fbdev-VIA: Deletion of an unnecessary check before the function call "framebuffer_release"
  video: fbdev-MMP: Deletion of an unnecessary check before the function call "mmp_unregister_path"
  video: mx3fb: Deletion of an unnecessary check before the function call "backlight_device_unregister"
  video: fbdev-OMAP2: Deletion of unnecessary checks before the function call "i2c_put_adapter"
  video: fbdev-SIS: Deletion of unnecessary checks before the function call "pci_dev_put"
  video: smscufx: Deletion of unnecessary checks before the function call "vfree"
  video: udlfb: Deletion of unnecessary checks before the function call "vfree"
  video: uvesafb: Deletion of an unnecessary check before the function call "uvesafb_free"
  video: fbdev-LCDC: Deletion of an unnecessary check before the function call "vfree"
  video: fbdev: arkfb: suppress build warning
  video: fbdev: s3fb: suppress build warning
  video: fbdev: vt8623fb: suppress build warning
  OMAPDSS: hdmi5: Fix bit field for IEC958_AES2_CON_SOURCE
  OMAPDSS: hdmi: Remove __exit qualifier from hdmi_uninit_output()
  OMAPDSS: hdmi5: Change hdmi_wp idlemode to to no_idle for audio playback
  OMAPDSS: Remove all references to obsolete HDMI audio callbacks
  ASoC: omap: Remove obsolete HDMI audio code and Kconfig options
  OMAPDSS: hdmi5: Register ASoC platform device for omap hdmi audio
  OMAPDSS: hdmi5: Remove callbacks for the old ASoC DAI driver
  ...

Pull virtio updates from Michael Tsirkin:
 "virtio: virtio 1.0 support, misc patches

  This adds a lot of infrastructure for virtio 1.0 support.  Notable
  missing pieces: virtio pci, virtio balloon (needs spec extension),
  vhost scsi.

  Plus, there are some minor fixes in a couple of places.

  Note: some net drivers are affected by these patches.  David said he's
  fine with merging these patches through my tree.

  Rusty's on vacation, he acked using my tree for these, too"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (70 commits)
  virtio_ccw: finalize_features error handling
  virtio_ccw: future-proof finalize_features
  virtio_pci: rename virtio_pci -> virtio_pci_common
  virtio_pci: update file descriptions and copyright
  virtio_pci: split out legacy device support
  virtio_pci: setup config vector indirectly
  virtio_pci: setup vqs indirectly
  virtio_pci: delete vqs indirectly
  virtio_pci: use priv for vq notification
  virtio_pci: free up vq->priv
  virtio_pci: fix coding style for structs
  virtio_pci: add isr field
  virtio: drop legacy_only driver flag
  virtio_balloon: drop legacy_only driver flag
  virtio_ccw: rev 1 devices set VIRTIO_F_VERSION_1
  virtio: allow finalize_features to fail
  virtio_ccw: legacy: don't negotiate rev 1/features
  virtio: add API to detect legacy devices
  virtio_console: fix sparse warnings
  vhost: remove unnecessary forward declarations in vhost.h
  ...

Pull mailbox framework updates from Jassi Brar.

* 'mailbox-devel' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
  Mailbox: Add support for Platform Communication Channel
  mailbox/omap: adapt to the new mailbox framework
  mailbox: add tx_prepare client callback
  mailbox: Don't unnecessarily re-arm the polling timer

Pull spi updates from Mark Brown:
 "Not a huge amount going on this release, mainly new drivers (there's a
  couple more waiting that didn't quite make the cut for this release
  too):

   - An interface for querying if the current transfer is the last in a
     message, allowing controllers that need special handling for the
     final transfer to use the core message parsing.
   - Support for Amlogic Meson SPIFC, Imagination Technologies SFPI,
     Intel Quark X1000 and Samsung Exynos 7 controllers"

* tag 'spi-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (38 commits)
  spi/s3c64xx: Remove redundant runtime PM management
  spi: fsl-spi: remove unused variable assignment
  spi: spi-fsl-spi: Return an error code in fsl_spi_do_one_msg()
  spi: core: Do not mangle error code from kthread_run()
  spi: fsl-espi: add (un)prepare_transfer_hardware calls to save power if SPI is not in use
  spi: fsl-(e)spi: migrate to generic master queueing
  spi/txx9: Deletion of an unnecessary check before the function call "clk_disable"
  spi: cadence: Fix 3-to-8 mux mode
  spi: cadence: Init HW after reading devicetree attributes
  spi: meson: Select REGMAP_MMIO
  spi: s3c64xx: add support for exynos7 SPI controller
  spi: spi-pxa2xx: SPI support for Intel Quark X1000
  spi: meson: meson_spifc_setup_speed() can be static
  spi: spi-pxa2xx: Add helpers for regiseters' accessing
  spi: spi-mxs: Fix mapping from vmalloc-ed buffer to scatter list
  spi: atmel: introduce probe deferring
  spi: atmel: remove compat for non DT board when requesting dma chan
  spi: meson: Add support for Amlogic Meson SPIFC
  spi: meson: Add device tree bindings documentation for SPIFC
  spi: core: Add spi_transfer_is_last() helper
  ...

Pull edac updates from Mauro Carvalho Chehab:
 - Broadwell-DE support on sb-edac driver
 - Some fixes at sb-edac driver

* tag 'edac/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac:
  sb_edac: Fix typo computing number of banks
  sb_edac: Add support for Broadwell-DE processor
  sb_edac: Fix discovery of top-of-low-memory for Haswell
  sb_edac: Fix erroneous bytes->gigabytes conversion
  sb_edac: Fix off-by-one error in number of channels

Currently, when trying to reuse a socket, vxlan_sock_add will grab
vn->sock_lock, locate a reusable socket, inc refcount and release
vn->sock_lock.

But vxlan_sock_release() will first decrement refcount, and then grab
that lock. refcnt operations are atomic but as currently we have
deferred works which hold vs->refcnt each, this might happen, leading to
a use after free (specially after vxlan_igmp_leave):

  CPU 1                            CPU 2

deferred work                    vxlan_sock_add
  ...                              ...
                                   spin_lock(&vn->sock_lock)
                                   vs = vxlan_find_sock();
  vxlan_sock_release
    dec vs->refcnt, reaches 0
    spin_lock(&vn->sock_lock)
                                   vxlan_sock_hold(vs), refcnt=1
                                   spin_unlock(&vn->sock_lock)
    hlist_del_rcu(&vs->hlist);
    vxlan_notify_del_rx_port(vs)
    spin_unlock(&vn->sock_lock)

So when we look for a reusable socket, we check if it wasn't freed
already before reusing it.

Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Fixes: 7c47cedf

 ("vxlan: move IGMP join/leave to work queue")
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull media updates from Mauro Carvalho Chehab:
 - Two new dvb frontend drivers: mn88472 and mn88473
 - A new driver for some PCIe DVBSky cards
 - A new remote controller driver: meson-ir
 - One LIRC staging driver got rewritten and promoted to mainstream:
   igorplugusb
 - A new tuner driver (m88rs6000t)
 - The old omap2 media driver got removed from staging.  This driver
   uses an old DMA API and it is likely broken on recent kernels.
   Nobody cared enough to fix it
 - Media bus format moved to a separate header, as DRM will also use the
   definitions there
 - mem2mem_testdev were renamed to vim2m, in order to use the same
   naming convention taken by the other virtual test driver (vivid)
 - Added a new driver for coda SoC (coda-jpeg)
 - The cx88 driver got converted to use videobuf2 core
 - Make DMABUF export buffer to work with DMA Scatter/Gather and Vmalloc
   cores
 - Lots of other fixes, improvements and cleanups on the drivers.

* tag 'media/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (384 commits)
  [media] mn88473: One function call less in mn88473_init() after error
  [media] mn88473: Remove uneeded check before release_firmware()
  [media] lirc_zilog: Deletion of unnecessary checks before vfree()
  [media] MAINTAINERS: Add myself as img-ir maintainer
  [media] img-ir: Don't set driver's module owner
  [media] img-ir: Depend on METAG or MIPS or COMPILE_TEST
  [media] img-ir/hw: Drop [un]register_decoder declarations
  [media] img-ir/hw: Fix potential deadlock stopping timer
  [media] img-ir/hw: Always read data to clear buffer
  [media] redrat3: ensure dma is setup properly
  [media] ddbridge: remove unneeded check before dvb_unregister_device()
  [media] si2157: One function call less in si2157_init() after error
  [media] tuners: remove uneeded checks before release_firmware()
  [media] arm: omap2: rx51-peripherals: fix build warning
  [media] stv090x: add an extra protetion against buffer overflow
  [media] stv090x: Remove an unreachable code
  [media] stv090x: Some whitespace cleanups
  [media] em28xx: checkpatch cleanup: whitespaces/new lines cleanups
  [media] si2168: add support for firmware files in new format
  [media] si2168: debug printout for firmware version
  ...

Or Gerlitz says:

====================
mlx4 driver update

This series from Matan, Jenny, Dotan and myself is mostly about adding
support to a new performance optimized flow steering mode (patches 4-10).

The 1st two patches are small fixes (one for VXLAN and one for SRIOV),
and the third patch is a fix to avoid hard-lockup situation when many
(hunderds) processes holding user-space QPs/CQs get events.

Matan and Or.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Add the required firmware commands for A0 steering and a way to enable
that. The firmware support focuses on INIT_HCA, QUERY_HCA, QUERY_PORT,
QUERY_DEV_CAP and QUERY_FUNC_CAP commands. Those commands are used
to configure and query the device.

The different A0 DMFS (steering) modes are:

Static - optimized performance, but flow steering rules are
limited. This mode should be choosed explicitly by the user
in order to be used.

Dynamic - this mode should be explicitly choosed by the user.
In this mode, the FW works in optimized steering mode as long as
it can and afterwards automatically drops to classic (full) DMFS.

Disable - this mode should be explicitly choosed by the user.
The user instructs the system not to use optimized steering, even if
the FW supports Dynamic A0 DMFS (and thus will be able to use optimized
steering in Default A0 DMFS mode).

Default - this mode is implicitly choosed. In this mode, if the FW
supports Dynamic A0 DMFS, it'll work in this mode. Otherwise, it'll
work at Disable A0 DMFS mode.

Under SRIOV configuration, when the A0 steering mode is enabled,
older guest VF drivers who aren't using the RX QP allocation flag
(MLX4_RESERVE_A0_QP) will get a QP from the general range and
fail when attempting to register a steering rule. To avoid that,
the PF context behaviour is changed once on A0 static mode, to
require support for the allocation flag in VF drivers too.

In order to enable A0 steering, we use log_num_mgm_entry_size param.
If the value of the parameter is not positive, we treat the absolute
value of log_num_mgm_entry_size as a bit field. Setting bit 2 of this
bit field enables static A0 steering.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently QUERY_PORT is done as a part of QUERY_DEV_CAP firmware command.

Since we would like to use it without querying all device capabilities,
extract this part to be a function of its own.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a given flow steering rule is invalid in respect to the current
steering configuration, print the correct error message to the system log.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A0 hybrid steering is a form of high performance flow steering.
By using this mode, mlx4 cards use a fast limited table based steering,
in order to enable fast steering of unicast packets to a QP.

In order to implement A0 hybrid steering we allocate resources
from different zones:
(1) General range
(2) Special MAC-assigned QPs [RSS, Raw-Ethernet] each has its own region.

When we create a rss QP or a raw ethernet (A0 steerable and BF ready) QP,
we try hard to allocate the QP from range (2). Otherwise, we try hard not
to allocate from this  range. However, when the system is pushed to its
limits and one needs every resource, the allocator uses every region it can.

Meaning, when we run out of raw-eth qps, the allocator allocates from the
general range (and the special-A0 area is no longer active). If we run out
of RSS qps, the mechanism tries to allocate from the raw-eth QP zone. If that
is also exhausted, the allocator will allocate from the general range
(and the A0 region is no longer active).

Note that if a raw-eth qp is allocated from the general range, it attempts
to allocate the range such that bits 6 and 7 (blueflame bits) in the
QP number are not set.

When the feature is used in SRIOV, the VF has to notify the PF what
kind of QP attributes it needs. In order to do that, along with the
"Eth QP blueflame" bit, we reserve a new "A0 steerable QP". According
to the combination of these bits, the PF tries to allocate a suitable QP.

In order to maintain backward compatibility (with older PFs), the PF
notifies which QP attributes it supports via QUERY_FUNC_CAP command.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The zone allocator is a mechanism which manages a few mlx4_bitmaps.

When allocating a resource, the user indicates the desired zone of
which this resource will be allocated from. If possible, the resource
will be allocated from this zone. Otherwise, the resource will be
allocated from a less-than, equal-to, higher-than priority zone,
according to the desired zone's properties with that respective
allocation order.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The number of reserved QPs is affected both from the firmware and
from the driver's requirements. This patch adds a check that
validates that this number is indeed feasable.

Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When using BF (Blue-Flame), the QPN overrides the VLAN, CV, and SV fields
in the WQE. Thus, BF may only be used for QPNs with bits 6,7 unset.

The current Ethernet driver code reserves a Tx QP range with 256b alignment.

This is wrong because if there are more than 64 Tx QPs in use,
QPNs >= base + 65 will have bits 6/7 set.

This problem is not specific for the Ethernet driver, any entity that
tries to reserve more than 64 BF-enabled QPs should fail. Also, using
ranges is not necessary here and is wasteful.

The new mechanism introduced here will support reservation for
"Eth QPs eligible for BF" for all drivers: bare-metal, multi-PF, and VFs
(when hypervisors support WC in VMs). The flow we use is:

1. In mlx4_en, allocate Tx QPs one by one instead of a range allocation,
   and request "BF enabled QPs" if BF is supported for the function

2. In the ALLOC_RES FW command, change param1 to:
a. param1[23:0]  - number of QPs
b. param1[31-24] - flags controlling QPs reservation

Bit 31 refers to Eth blueflame supported QPs. Those QPs must have
bits 6 and 7 unset in order to be used in Ethernet.

Bits 24-30 of the flags are currently reserved.

When a function tries to allocate a QP, it states the required attributes
for this QP. Those attributes are considered "best-effort". If an attribute,
such as Ethernet BF enabled QP, is a must-have attribute, the function has
to check that attribute is supported before trying to do the allocation.

In a lower layer of the code, mlx4_qp_reserve_range masks out the bits
which are unsupported. If SRIOV is used, the PF validates those attributes
and masks out unsupported attributes as well. In order to notify VFs which
attributes are supported, the VF uses QUERY_FUNC_CAP command. This command's
mailbox is filled by the PF, which notifies which QP allocation attributes
it supports.

Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously, we've fired all our completion callbacks straight from our ISR.

Some of those callbacks were lightweight (for example, mlx4_en's and
IPoIB napi callbacks), but some of them did more work (for example,
the user-space RDMA stack uverbs' completion handler). Besides that,
doing more than the minimal work in ISR is generally considered wrong,
it could even lead to a hard lockup of the system. Since when a lot
of completion events are generated by the hardware, the loop over those
events could be so long, that we'll get into a hard lockup by the system
watchdog.

In order to avoid that, add a new way of invoking completion events
callbacks. In the interrupt itself, we add the CQs which receive completion
event to a per-EQ list and schedule a tasklet. In the tasklet context
we loop over all the CQs in the list and invoke the user callback.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When VFs (guests in this context) issue the QUERY_DEV_CAP command, they
need not be told that host side virtualization features such as VST, FSM
(MAC anti-spoofing) and running > 80 VFs are supported by the device.

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This was dropped by mistake for the napi_gro_frags flow, fix that.

Fixes: dd65beac

 ('net/mlx4_en: Extend usage of napi_gro_frags')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull backlight updates from Lee Jones:
 - Clean-up leaky resources; pwm_bl
 - Simplify Device Tree initialisation; lp855x_bl
 - Add Regulator support; lp855x
 - Remove Bryan from the Maintainer list -- new baby, no time :)

* tag 'backlight-for-linus-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
  MAINTAINERS: Remove my name from Backlight subsystem
  backlight: lp855x: Add supply regulator to lp855x
  backlight: lp855x: Refactor DT parsing code
  backlight: pwm: Clean-up pwm requested using legacy API

The encapsulated offload flags shouldn't be unconditionally exported
to the stack. The stack expects offloading to work across all tunnel
types when those flags are set. This would break other tunnels (like
GRE) since be2net currently supports tunnel offload for VxLAN only.

Also, with VxLANs Skyhawk-R can offload only 1 UDP dport. If more
than 1 UDP port is added, we should disable offloads in that case too.

Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to use dma_mapping_error() to check the dma address returned
by dma_map_single/page(). Otherwise we would get warning like this:
  WARNING: at lib/dma-debug.c:1140
  Modules linked in:
  CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.18.0-rc2-next-20141029 #196
  task: c0834300 ti: effe6000 task.ti: c0874000
  NIP: c02b2c98 LR: c02b2c98 CTR: c030abc4
  REGS: effe7d70 TRAP: 0700   Not tainted  (3.18.0-rc2-next-20141029)
  MSR: 00021000 <CE,ME>  CR: 22044022  XER: 20000000

  GPR00: c02b2c98 effe7e20 c0834300 00000098 00021000 00000000 c030b898 00000003
  GPR08: 00000001 00000000 00000001 749eec9d 22044022 1001abe0 00000020 ef278678
  GPR16: ef278670 ef278668 ef278660 070a8040 c087f99c c08cdc60 00029000 c0840d44
  GPR24: c08be6e8 c0840000 effe7e78 ef041340 00000600 ef114e10 00000000 c08be6e0
  NIP [c02b2c98] check_unmap+0x51c/0x9e4
  LR [c02b2c98] check_unmap+0x51c/0x9e4
  Call Trace:
  [effe7e20] [c02b2c98] check_unmap+0x51c/0x9e4 (unreliable)
  [effe7e70] [c02b31d8] debug_dma_unmap_page+0x78/0x8c
  [effe7ed0] [c03d1640] gfar_clean_rx_ring+0x208/0x488
  [effe7f40] [c03d1a9c] gfar_poll_rx_sq+0x3c/0xa8
  [effe7f60] [c04f8714] net_rx_action+0xc0/0x178
  [effe7f90] [c00435a0] __do_softirq+0x100/0x1fc
  [effe7fe0] [c0043958] irq_exit+0xa4/0xc8
  [effe7ff0] [c000d14c] call_do_irq+0x24/0x3c
  [c0875e90] [c00048a0] do_IRQ+0x8c/0xf8
  [c0875eb0] [c000ed10] ret_from_except+0x0/0x18

For TX, we need to unmap the pages which has already been mapped and
free the skb before return.

For RX, move the dma mapping and error check to gfar_new_skb(). We
would reuse the original skb in the rx ring when either allocating
skb failure or dma mapping error.

Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove use of calls into t4_fw_hello() with MASTER_MUST, which results in
FW_HELLO_CMD_MASTERFORCE being set. The firmware doesn't support this and of
course any existing PF Drivers will totally go for a toss.

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull pin control changes from Linus Walleij:
 "Here is a stash of pin control changes I have collected for the v3.19
  series.  Mainly new hardware support, with Intels new embedded SoC as
  the especially interesting thing standing out, fully using the
  subsystem.

   - Force conversion of the ux500 pin control device trees and parsers
     to use the generic pin control bindings.
   - New driver and device tree bindings for the Qualcomm PMIC MPP pin
     controller and GPIO.
   - Some ACPI infrastructure for pin controllers.
   - New driver for the Intel CherryView/Braswell pin controller, the
     first Intel pin controller to fully take advantage of the pin
     control subsystem.
   - Support the Freescale i.MX VF610 variant.
   - Support the sunxi A80 variant.
   - Support the Samsung Exynos 4415 and Exynos 7 variants.
   - Split out Intel pin controllers to their own subdirectory.
   - A large slew of rockchip pin control updates, including
     suspend/resume support.
   - A large slew of Samsung Exynos pin controller updates.
   - Various minor updates and fixes"

* tag 'pinctrl-v3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (49 commits)
  pinctrl: at91: enhance (debugfs) at91_gpio_dbg_show
  pinctrl: meson: add device tree bindings documentation
  gpio: tz1090: Fix error handling of irq_of_parse_and_map
  pinctrl: tz1090-pinctrl.txt: Fix typo in binding
  pinctrl: pinconf-generic: Declare dt_params/conf_items const
  pinctrl: exynos: Add support for Exynos4415
  pinctrl: exynos: Add initial driver data for Exynos7
  pinctrl: exynos: Add irq_chip instance for Exynos7 wakeup interrupts
  pinctrl: exynos: Consolidate irq domain callbacks
  pinctrl: exynos: Generalize the eint16_31 demux code
  pinctrl: samsung: Separate per-bank init and runtime data
  pinctrl: samsung: Constify samsung_pin_ctrl struct
  pinctrl: samsung: Constify samsung_pin_bank_type struct
  pinctrl: samsung: Drop unused label field in samsung_pin_ctrl struct
  pinctrl: samsung: Make samsung_pinctrl_get_soc_data use ERR_PTR()
  pinctrl: Add Intel Cherryview/Braswell pin controller support
  gpio / ACPI: Add knowledge about pin controllers to acpi_get_gpiod()
  pinctrl: Fix path error in documentation
  pinctrl: rockchip: save and restore gpio6_c6 pinmux in suspend/resume
  pinctrl: rockchip: add suspend/resume functions
  ...

Pull ACPI and power management updates from Rafael Wysocki:
 "This time we have some more new material than we used to have during
  the last couple of development cycles.

  The most important part of it to me is the introduction of a unified
  interface for accessing device properties provided by platform
  firmware.  It works with Device Trees and ACPI in a uniform way and
  drivers using it need not worry about where the properties come from
  as long as the platform firmware (either DT or ACPI) makes them
  available.  It covers both devices and "bare" device node objects
  without struct device representation as that turns out to be necessary
  in some cases.  This has been in the works for quite a few months (and
  development cycles) and has been approved by all of the relevant
  maintainers.

  On top of that, some drivers are switched over to the new interface
  (at25, leds-gpio, gpio_keys_polled) and some additional changes are
  made to the core GPIO subsystem to allow device drivers to manipulate
  GPIOs in the "canonical" way on platforms that provide GPIO
  information in their ACPI tables, but don't assign names to GPIO lines
  (in which case the driver needs to do that on the basis of what it
  knows about the device in question).  That also has been approved by
  the GPIO core maintainers and the rfkill driver is now going to use
  it.

  Second is support for hardware P-states in the intel_pstate driver.
  It uses CPUID to detect whether or not the feature is supported by the
  processor in which case it will be enabled by default.  However, it
  can be disabled entirely from the kernel command line if necessary.

  Next is support for a platform firmware interface based on ACPI
  operation regions used by the PMIC (Power Management Integrated
  Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
  That interface is used for manipulating power resources and for
  thermal management: sensor temperature reporting, trip point setting
  and so on.

  Also the ACPI core is now going to support the _DEP configuration
  information in a limited way.  Basically, _DEP it supposed to reflect
  off-the-hierarchy dependencies between devices which may be very
  indirect, like when AML for one device accesses locations in an
  operation region handled by another device's driver (usually, the
  device depended on this way is a serial bus or GPIO controller).  The
  support added this time is sufficient to make the ACPI battery driver
  work on Asus T100A, but it is general enough to be able to cover some
  other use cases in the future.

  Finally, we have a new cpufreq driver for the Loongson1B processor.

  In addition to the above, there are fixes and cleanups all over the
  place as usual and a traditional ACPICA update to a recent upstream
  release.

  As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
  Intel platforms should be able to handle power management of the DMA
  engine correctly, the cpufreq-dt driver should interact with the
  thermal subsystem in a better way and the ACPI backlight driver should
  handle some more corner cases, among other things.

  On top of the ACPICA update there are fixes for race conditions in the
  ACPICA's interrupt handling code which might lead to some random and
  strange looking failures on some systems.

  In the cleanups department the most visible part is the series of
  commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
  option.  That was triggered by a discussion regarding the generic
  power domains code during which we realized that trying to support
  certain combinations of PM config options was painful and not really
  worth it, because nobody would use them in production anyway.  For
  this reason, we decided to make CONFIG_PM_SLEEP select
  CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
  became redundant and CONFIG_PM could be used instead of it.  The
  material here makes that replacement in a major part of the tree, but
  there will be at least one more batch of that in the second part of
  the merge window.

  Specifics:

   - Support for retrieving device properties information from ACPI _DSD
     device configuration objects and a unified device properties
     interface for device drivers (and subsystems) on top of that.  As
     stated above, this works with Device Trees and ACPI and allows
     device drivers to be written in a platform firmware (DT or ACPI)
     agnostic way.  The at25, leds-gpio and gpio_keys_polled drivers are
     now going to use this new interface and the GPIO subsystem is
     additionally modified to allow device drivers to assign names to
     GPIO resources returned by ACPI _CRS objects (in case _DSD is not
     present or does not provide the expected data).  The changes in
     this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
     Lu, and Darren Hart with some fixes from others (Fabio Estevam,
     Geert Uytterhoeven).

   - Support for Hardware Managed Performance States (HWP) as described
     in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
     driver.  CPUID is used to detect whether or not the feature is
     supported by the processor.  If supported, it will be enabled
     automatically unless the intel_pstate=no_hwp switch is present in
     the kernel command line.  From Dirk Brandewie.

   - New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).

   - Support for firmware interface based on ACPI operation regions used
     by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
     platforms for power resource control and thermal management (Aaron
     Lu).

   - Limited support for retrieving off-the-hierarchy dependencies
     between devices from ACPI _DEP device configuration objects and
     deferred probing support for the ACPI battery driver based on the
     _DEP information to make that driver work on Asus T100A (Lan
     Tianyu).

   - New cpufreq driver for the Loongson1B processor (Kelvin Cheung).

   - ACPICA update to upstream revision 20141107 which only affects
     tools (Bob Moore).

   - Fixes for race conditions in the ACPICA's interrupt handling code
     and in the ACPI code related to system suspend and resume (Lv Zheng
     and Rafael J Wysocki).

   - ACPI core fix for an RCU-related issue in the ioremap() regions
     management code that slowed down significantly after CPUs had been
     allowed to enter idle states even if they'd had RCU callbakcs
     queued and triggered some problems in certain proprietary graphics
     driver (and elsewhere).  The fix replaces synchronize_rcu() in that
     code with synchronize_rcu_expedited() which makes the issue go
     away.  From Konstantin Khlebnikov.

   - ACPI LPSS (Low-Power Subsystem) driver fix to handle power
     management of the DMA engine included into the LPSS correctly.  The
     problem is that the DMA engine doesn't have ACPI PM support of its
     own and it simply is turned off when the last LPSS device having
     ACPI PM support goes into D3cold.  To work around that, the PM
     domain used by the ACPI LPSS driver is redesigned so at least one
     device with ACPI PM support will be on as long as the DMA engine is
     in use.  From Andy Shevchenko.

   - ACPI backlight driver fix to avoid using it on "Win8-compatible"
     systems where it doesn't work and where it was used by default by
     mistake (Aaron Lu).

   - Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
     Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
     Chaugule (mostly related to the upcoming ARM64 support).

   - Intel RAPL (Running Average Power Limit) power capping driver fixes
     and improvements including new processor IDs (Jacob Pan).

   - Generic power domains modification to power up domains after
     attaching devices to them to meet the expectations of device
     drivers and bus types assuming devices to be accessible at probe
     time (Ulf Hansson).

   - Preliminary support for controlling device clocks from the generic
     power domains core code and modifications of the ARM/shmobile
     platform to use that feature (Ulf Hansson).

   - Assorted minor fixes and cleanups of the generic power domains core
     code (Ulf Hansson, Geert Uytterhoeven).

   - Assorted minor fixes and cleanups of the device clocks control code
     in the PM core (Geert Uytterhoeven, Grygorii Strashko).

   - Consolidation of device power management Kconfig options by making
     CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
     which is now redundant (Rafael J Wysocki and Kevin Hilman).  That
     is the first batch of the changes needed for this purpose.

   - Core device runtime power management support code cleanup related
     to the execution of callbacks (Andrzej Hajda).

   - cpuidle ARM support improvements (Lorenzo Pieralisi).

   - cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
     new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
     Bartlomiej Zolnierkiewicz).

   - New cpufreq driver callback (->ready) to be executed when the
     cpufreq core is ready to use a given policy object and cpufreq-dt
     driver modification to use that callback for cooling device
     registration (Viresh Kumar).

   - cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
     Geboski, Tomeu Vizoso).

   - Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
     cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
     Stefan Wahren, Petr Cvek).

   - OPP (Operating Performance Points) framework modification to allow
     OPPs to be removed too and update of a few cpufreq drivers
     (cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
     during initialization) on driver removal (Viresh Kumar).

   - Hibernation core fixes and cleanups (Tina Ruchandani and Markus
     Elfring).

   - PM Kconfig fix related to CPU power management (Pankaj Dubey).

   - cpupower tool fix (Prarit Bhargava)"

* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
  i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
  dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  tools: cpupower: fix return checks for sysfs_get_idlestate_count()
  drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
  MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  leds: leds-gpio: Fix multiple instances registration without 'label' property
  iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
  block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
  PM: Merge the SET*_RUNTIME_PM_OPS() macros
  ...