- Dec 09, 2015
-
-
Greg Kroah-Hartman authored
-
Clemens Ladisch authored
commit a91e627e upstream. One of the many faults of the QinHeng CH345 USB MIDI interface chip is that it does not handle received SysEx messages correctly -- every second event packet has a wrong code index number, which is the one from the last seen message, instead of 4. For example, the two messages "FE F0 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E F7" result in the following event packets: correct: CH345: 0F FE 00 00 0F FE 00 00 04 F0 01 02 04 F0 01 02 04 03 04 05 0F 03 04 05 04 06 07 08 04 06 07 08 04 09 0A 0B 0F 09 0A 0B 04 0C 0D 0E 04 0C 0D 0E 05 F7 00 00 05 F7 00 00 A class-compliant driver must interpret an event packet with CIN 15 as having a single data byte, so the other two bytes would be ignored. The message received by the host would then be missing two bytes out of six; in this example, "F0 01 02 03 06 07 08 09 0C 0D 0E F7". These corrupted SysEx event packages contain only data bytes, while the CH345 uses event packets with a correct CIN value only for messages with a status byte, so it is possible to distinguish between these two cases by checking for the presence of this status byte. (Other bugs in the CH345's input handling, such as the corruption resulting from running status, cannot be worked around.) Signed-off-by:
Clemens Ladisch <clemens@ladisch.de> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Clemens Ladisch authored
commit 1ca8b201 upstream. The CH345 USB MIDI chip has two output ports. However, they are multiplexed through one pin, and the number of ports cannot be reduced even for hardware that implements only one connector, so for those devices, data sent to either port ends up on the same hardware output. This becomes a problem when both ports are used at the same time, as longer MIDI commands (such as SysEx messages) are likely to be interrupted by messages from the other port, and thus to get lost. It would not be possible for the driver to detect how many ports the device actually has, except that in practice, _all_ devices built with the CH345 have only one port. So we can just ignore the device's descriptors, and hardcode one output port. Signed-off-by:
-
Clemens Ladisch authored
commit 98d362be upstream. Signed-off-by:
-
Bjørn Mork authored
commit 638148e2 upstream. Thomas reports " 4gsystems sells two total different LTE-surfsticks under the same name. .. The newer version of XS Stick W100 is from "omega" .. Under windows the driver switches to the same ID, and uses MI03\6 for network and MI01\6 for modem. .. echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1c9e ProdID=9b01 Rev=02.32 S: Manufacturer=USB Modem S: Product=USB Modem S: SerialNumber= C: #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage Now all important things are there: wwp0s29f7u2i3 (net), ttyUSB2 (at), cdc-wdm0 (qmi), ttyUSB1 (at) There is also ttyUSB0, but it is not usable, at least not for at. The device works well with qmi and ModemManager-NetworkManager. " Reported-by:
Thomas Schäfer <tschaefer@t-online.de> Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Aleksander Morgado authored
commit e07af133 upstream. Also known as Verizon U620L. The device is modeswitched from 1410:9020 to 1410:9022 by selecting the 4th USB configuration: $ sudo usb_modeswitch –v 0x1410 –p 0x9020 –u 4 This configuration provides a ECM interface as well as TTYs ('Enterprise Mode' according to the U620 Linux integration guide). Signed-off-by:
Aleksander Morgado <aleksander@aleksander.es> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Uwe Kleine-König authored
commit 705e63d2 upstream. There is a bit of a mess in the order of arguments to the ulpi write callback. There is int ulpi_write(struct ulpi *ulpi, u8 addr, u8 val) in drivers/usb/common/ulpi.c; struct usb_phy_io_ops { ... int (*write)(struct usb_phy *x, u32 val, u32 reg); } in include/linux/usb/phy.h. The callback registered by the musb driver has to comply to the latter, but up to now had "offset" first which effectively made the function broken for correct users. So flip the order and while at it also switch to the parameter names of struct usb_phy_io_ops's write. Fixes: ffb865b1 ("usb: musb: add ulpi access operations") Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Jiri Slaby authored
commit 19cd80a2 upstream. It is not permitted to set task state before lock. usblp_wwait sets the state to TASK_INTERRUPTIBLE and calls mutex_lock_interruptible. Upon return from that function, the state will be TASK_RUNNING again. This is clearly a bug and a warning is generated with LOCKDEP too: WARNING: CPU: 1 PID: 5109 at kernel/sched/core.c:7404 __might_sleep+0x7d/0x90() do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffffa0c588d0>] usblp_wwait+0xa0/0x310 [usblp] Modules linked in: ... CPU: 1 PID: 5109 Comm: captmon Tainted: G W 4.2.5-0.gef2823b-default #1 Hardware name: LENOVO 23252SG/23252SG, BIOS G2ET33WW (1.13 ) 07/24/2012 ffffffff81a4edce ffff880236ec7ba8 ffffffff81716651 0000000000000000 ffff880236ec7bf8 ffff880236ec7be8 ffffffff8106e146 0000000000000282 ffffffff81a50119 000000000000028b 0000000000000000 ffff8802dab7c508 Call Trace: ... [<ffffffff8106e1c6>] warn_slowpath_fmt+0x46/0x50 [<ffffffff8109a8bd>] __might_sleep+0x7d/0x90 [<ffffffff8171b20f>] mutex_lock_interruptible_nested+0x2f/0x4b0 [<ffffffffa0c588fc>] usblp_wwait+0xcc/0x310 [usblp] [<ffffffffa0c58bb2>] usblp_write+0x72/0x350 [usblp] [<ffffffff8121ed98>] __vfs_write+0x28/0xf0 ... Commit 7f477358 (usblp: Implement the ENOSPC convention) moved the set prior locking. So move it back after the lock. Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Fixes: 7f477358 ("usblp: Implement the ENOSPC convention") Acked-By:
Pete Zaitcev <zaitcev@yahoo.com> Signed-off-by:
-
Robin Murphy authored
commit 5accd17d upstream. For reasons not entirely apparent, but now enshrined in history, the architectural mapping of AArch32 banked registers to AArch64 registers actually orders SP_<mode> and LR_<mode> backwards compared to the intuitive r13/r14 order, for all modes except FIQ. Fix the compat_<reg>_<mode> macros accordingly, in the hope of avoiding subtle bugs with KVM and AArch32 guests. Signed-off-by:
Robin Murphy <robin.murphy@arm.com> Acked-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Mirza Krak authored
commit 7cecd9ab upstream. According to SJA1000 data sheet error-warning (EI) interrupt is not cleared by setting the controller in to reset-mode. Then if we have the following case: - system is suspended (echo mem > /sys/power/state) and SJA1000 is left in operating state - A bus error condition occurs which activates EI interrupt, system is still suspended which means EI interrupt will be not be handled nor cleared. If the above two events occur, on resume there is no way to return the SJA1000 to operating state, except to cycle power to it. By simply reading the IR register on start we will clear any previous conditions that could be present. Signed-off-by:
Mirza Krak <mirza.krak@hostmobility.com> Reported-by:
Christian Magnusson <Christian.Magnusson@semcon.com> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
David Herrmann authored
commit 660f0fc0 upstream. The HIDP specs define an idle-timeout which automatically disconnects a device. This has always been implemented in the HIDP layer and forced a synchronous shutdown of the hidp-scheduler. This works just fine, but lacks a forced disconnect on the underlying l2cap channels. This has been broken since: commit 5205185d Author: David Herrmann <dh.herrmann@gmail.com> Date: Sat Apr 6 20:28:47 2013 +0200 Bluetooth: hidp: remove old session-management The old session-management always forced an l2cap error on the ctrl/intr channels when shutting down. The new session-management skips this, as we don't want to enforce channel policy on the caller. In other words, if user-space removes an HIDP device, the underlying channels (which are *owned* and *referenced* by user-space) are still left active. User-space needs to call shutdown(2) or close(2) to release them. Unfortunately, this does not work with idle-timeouts. There is no way to signal user-space that the HIDP layer has been stopped. The API simply does not support any event-passing except for poll(2). Hence, we restore old behavior and force EUNATCH on the sockets if the HIDP layer is disconnected due to idle-timeouts (behavior of explicit disconnects remains unmodified). User-space can still call getsockopt(..., SO_ERROR, ...) ..to retrieve the EUNATCH error and clear sk_err. Hence, the channels can still be re-used (which nobody does so far, though). Therefore, the API still supports the new behavior, but with this patch it's also compatible to the old implicit channel shutdown. Reported-by:
Mark Haun <haunma@keteu.org> Reported-by:
Luiz Augusto von Dentz <luiz.dentz@gmail.com> Signed-off-by:
David Herrmann <dh.herrmann@gmail.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Larry Finger authored
commit 1e6e6328 upstream. This adds the USB ID for the Sitecom WLA2100. The Windows 10 inf file was checked to verify that the addition is correct. Reported-by:
Frans van de Wiel <fvdw@fvdw.eu> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: Frans van de Wiel <fvdw@fvdw.eu> Signed-off-by:
-
Dan Carpenter authored
commit 1f9c6e1b upstream. There were several bugs here. 1) The done label was in the wrong place so we didn't copy any information out when there was no command given. 2) We were using PAGE_SIZE as the size of the buffer instead of "PAGE_SIZE - pos". 3) snprintf() returns the number of characters that would have been printed if there were enough space. If there was not enough space (and we had fixed the memory corruption bug #2) then it would result in an information leak when we do simple_read_from_buffer(). I've changed it to use scnprintf() instead. I also removed the initialization at the start of the function, because I thought it made the code a little more clear. Fixes: 5e6e3a92 ('wireless: mwifiex: initial commit for Marvell mwifiex driver') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Maxime Ripard authored
commit 2502d0ef upstream. The CPU_MAP register is duplicated for each CPUs at different addresses, each instance being at a different address. However, the code so far was using CONFIG_NR_CPUS to initialise the CPU_MAP registers for each registers, while the SoCs embed at most 4 CPUs. This is especially an issue with multi_v7_defconfig, where CONFIG_NR_CPUS is currently set to 16, resulting in writes to registers that are not CPU_MAP. Fixes: c5aff182 ("net: mvneta: driver for Marvell Armada 370/XP network unit") Signed-off-by:
Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Johannes Berg authored
commit 8ec6d978 upstream. The ifmgd->ave_beacon_signal value cannot be taken as is for comparisons, it must be divided by since it's represented like that for better accuracy of the EWMA calculations. This would lead to invalid driver RSSI events. Fix the used value. Fixes: 615f7b9b ("mac80211: add driver RSSI threshold events") Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Andrew Cooper authored
commit 581b7f15 upstream. There appears to be no formal statement of what pv_irq_ops.save_fl() is supposed to return precisely. Native returns the full flags, while lguest and Xen only return the Interrupt Flag, and both have comments by the implementations stating that only the Interrupt Flag is looked at. This may have been true when initially implemented, but no longer is. To make matters worse, the Xen PVOP leaves the upper bits undefined, making the BUG_ON() undefined behaviour. Experimentally, this now trips for 32bit PV guests on Broadwell hardware. The BUG_ON() is consistent for an individual build, but not consistent for all builds. It has also been a sitting timebomb since SMAP support was introduced. Use native_save_fl() instead, which will obtain an accurate view of the AC flag. Signed-off-by:
Andrew Cooper <andrew.cooper3@citrix.com> Reviewed-by:
David Vrabel <david.vrabel@citrix.com> Tested-by:
Rusty Russell <rusty@rustcorp.com.au> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: <lguest@lists.ozlabs.org> Cc: Xen-devel <xen-devel@lists.xen.org> Link: http://lkml.kernel.org/r/1433323874-6927-1-git-send-email-andrew.cooper3@citrix.com Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Borislav Petkov authored
commit 04633df0 upstream. When we get loaded by a 64-bit bootloader, kernel entry point is startup_64 in head_64.S. We don't trust any and all bootloaders because some will fiddle with CPU configuration so we go ahead and massage each CPU into sanity again. For example, some dell BIOSes have this XD disable feature which set IA32_MISC_ENABLE[34] and disable NX. This might be some dumb workaround for other OSes but Linux sure doesn't need it. A similar thing is present in the Surface 3 firmware - see https://bugzilla.kernel.org/show_bug.cgi?id=106051 - which sets this bit only on the BSP: # rdmsr -a 0x1a0 400850089 850089 850089 850089 I know, right?! There's not even an off switch in there. So fix all those cases by sanitizing the 64-bit entry point too. For that, make verify_cpu() callable in 64-bit mode also. Requested-and-debugged-by:
"H. Peter Anvin" <hpa@zytor.com> Reported-and-tested-by:
Bastien Nocera <bugzilla@hadess.net> Signed-off-by:
Borislav Petkov <bp@suse.de> Cc: Matt Fleming <matt@codeblueprint.co.uk> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1446739076-21303-1-git-send-email-bp@alien8.de Signed-off-by:
-
Krzysztof Mazur authored
commit 68accac3 upstream. The commit f5f3497c extended the low identity mapping. However, if the kernel uses more than 2 GB (VMSPLIT_2G_OPT or VMSPLIT_1G memory split), the normal memory mapping is overwritten by the low identity mapping causing a crash. To avoid overwritting, limit the low identity map to cover only memory before kernel range (PAGE_OFFSET). Fixes: f5f3497c "x86/setup: Extend low identity map to cover whole kernel range Signed-off-by:
Krzysztof Mazur <krzysiek@podlesie.net> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Laszlo Ersek <lersek@redhat.com> Cc: Matt Fleming <matt.fleming@intel.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Link: http://lkml.kernel.org/r/1446815916-22105-1-git-send-email-krzysiek@podlesie.net Signed-off-by:
-
Paolo Bonzini authored
commit f5f3497c upstream. On 32-bit systems, the initial_page_table is reused by efi_call_phys_prolog as an identity map to call SetVirtualAddressMap. efi_call_phys_prolog takes care of converting the current CPU's GDT to a physical address too. For PAE kernels the identity mapping is achieved by aliasing the first PDPE for the kernel memory mapping into the first PDPE of initial_page_table. This makes the EFI stub's trick "just work". However, for non-PAE kernels there is no guarantee that the identity mapping in the initial_page_table extends as far as the GDT; in this case, accesses to the GDT will cause a page fault (which quickly becomes a triple fault). Fix this by copying the kernel mappings from swapper_pg_dir to initial_page_table twice, both at PAGE_OFFSET and at identity mapping. For some reason, this is only reproducible with QEMU's dynamic translation mode, and not for example with KVM. However, even under KVM one can clearly see that the page table is bogus: $ qemu-system-i386 -pflash OVMF.fd -M q35 vmlinuz0 -s -S -daemonize $ gdb (gdb) target remote localhost:1234 (gdb) hb *0x02858f6f Hardware assisted breakpoint 1 at 0x2858f6f (gdb) c Continuing. Breakpoint 1, 0x02858f6f in ?? () (gdb) monitor info registers ... GDT= 0724e000 000000ff IDT= fffbb000 000007ff CR0=0005003b CR2=ff896000 CR3=032b7000 CR4=00000690 ... The page directory is sane: (gdb) x/4wx 0x32b7000 0x32b7000: 0x03398063 0x03399063 0x0339a063 0x0339b063 (gdb) x/4wx 0x3398000 0x3398000: 0x00000163 0x00001163 0x00002163 0x00003163 (gdb) x/4wx 0x3399000 0x3399000: 0x00400003 0x00401003 0x00402003 0x00403003 but our particular page directory entry is empty: (gdb) x/1wx 0x32b7000 + (0x724e000 >> 22) * 4 0x32b7070: 0x00000000 [ It appears that you can skate past this issue if you don't receive any interrupts while the bogus GDT pointer is loaded, or if you avoid reloading the segment registers in general. Andy Lutomirski provides some additional insight: "AFAICT it's entirely permissible for the GDTR and/or LDT descriptor to point to unmapped memory. Any attempt to use them (segment loads, interrupts, IRET, etc) will try to access that memory as if the access came from CPL 0 and, if the access fails, will generate a valid page fault with CR2 pointing into the GDT or LDT." Up until commit 23a0d4e8 ("efi: Disable interrupts around EFI calls, not in the epilog/prolog calls") interrupts were disabled around the prolog and epilog calls, and the functional GDT was re-installed before interrupts were re-enabled. Which explains why no one has hit this issue until now. ] Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Reported-by:
Laszlo Ersek <lersek@redhat.com> Cc: <stable@vger.kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Andy Lutomirski <luto@amacapital.net> Signed-off-by:
Matt Fleming <matt.fleming@intel.com> [ Updated changelog. ] Signed-off-by:
-
Florian Fainelli authored
commit d836ace6 upstream. DSA expects the host_dev pointer to be the device structure associated with the MDIO bus controller driver. First commit breaking that was c3a07134 ("mv643xx_eth: convert to use the Marvell Orion MDIO driver"), and then, it got completely under the radar for a while. Reported-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Marek Szyprowski authored
commit 7e312103 upstream. IOMMU-based dma_mmap() implementation lacked proper support for offset parameter used in mmap call (it always assumed that mapping starts from offset zero). This patch adds support for offset parameter to IOMMU-based implementation. Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Marek Szyprowski authored
commit 371f0f08 upstream. dma_mmap() function in IOMMU-based dma-mapping implementation lacked a check for valid range of mmap parameters (offset and buffer size), what might have caused access beyond the allocated buffer. This patch fixes this issue. Signed-off-by:
-
Sasha Levin authored
[ Upstream commit 74e98eb0 ] There was no verification that an underlying transport exists when creating a connection, this would cause dereferencing a NULL ptr. It might happen on sockets that weren't properly bound before attempting to send a message, which will cause a NULL ptr deref: [135546.047719] kasan: GPF could be caused by NULL-ptr deref or user memory accessgeneral protection fault: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC KASAN [135546.051270] Modules linked in: [135546.051781] CPU: 4 PID: 15650 Comm: trinity-c4 Not tainted 4.2.0-next-20150902-sasha-00041-gbaa1222-dirty #2527 [135546.053217] task: ffff8800835bc000 ti: ffff8800bc708000 task.ti: ffff8800bc708000 [135546.054291] RIP: __rds_conn_create (net/rds/connection.c:194) [135546.055666] RSP: 0018:ffff8800bc70fab0 EFLAGS: 00010202 [135546.056457] RAX: dffffc0000000000 RBX: 0000000000000f2c RCX: ffff8800835bc000 [135546.057494] RDX: 0000000000000007 RSI: ffff8800835bccd8 RDI: 0000000000000038 [135546.058530] RBP: ffff8800bc70fb18 R08: 0000000000000001 R09: 0000000000000000 [135546.059556] R10: ffffed014d7a3a23 R11: ffffed014d7a3a21 R12: 0000000000000000 [135546.060614] R13: 0000000000000001 R14: ffff8801ec3d0000 R15: 0000000000000000 [135546.061668] FS: 00007faad4ffb700(0000) GS:ffff880252000000(0000) knlGS:0000000000000000 [135546.062836] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [135546.063682] CR2: 000000000000846a CR3: 000000009d137000 CR4: 00000000000006a0 [135546.064723] Stack: [135546.065048] ffffffffafe2055c ffffffffafe23fc1 ffffed00493097bf ffff8801ec3d0008 [135546.066247] 0000000000000000 00000000000000d0 0000000000000000 ac194a24c0586342 [135546.067438] 1ffff100178e1f78 ffff880320581b00 ffff8800bc70fdd0 ffff880320581b00 [135546.068629] Call Trace: [135546.069028] ? __rds_conn_create (include/linux/rcupdate.h:856 net/rds/connection.c:134) [135546.069989] ? rds_message_copy_from_user (net/rds/message.c:298) [135546.071021] rds_conn_create_outgoing (net/rds/connection.c:278) [135546.071981] rds_sendmsg (net/rds/send.c:1058) [135546.072858] ? perf_trace_lock (include/trace/events/lock.h:38) [135546.073744] ? lockdep_init (kernel/locking/lockdep.c:3298) [135546.074577] ? rds_send_drop_to (net/rds/send.c:976) [135546.075508] ? __might_fault (./arch/x86/include/asm/current.h:14 mm/memory.c:3795) [135546.076349] ? __might_fault (mm/memory.c:3795) [135546.077179] ? rds_send_drop_to (net/rds/send.c:976) [135546.078114] sock_sendmsg (net/socket.c:611 net/socket.c:620) [135546.078856] SYSC_sendto (net/socket.c:1657) [135546.079596] ? SYSC_connect (net/socket.c:1628) [135546.080510] ? trace_dump_stack (kernel/trace/trace.c:1926) [135546.081397] ? ring_buffer_unlock_commit (kernel/trace/ring_buffer.c:2479 kernel/trace/ring_buffer.c:2558 kernel/trace/ring_buffer.c:2674) [135546.082390] ? trace_buffer_unlock_commit (kernel/trace/trace.c:1749) [135546.083410] ? trace_event_raw_event_sys_enter (include/trace/events/syscalls.h:16) [135546.084481] ? do_audit_syscall_entry (include/trace/events/syscalls.h:16) [135546.085438] ? trace_buffer_unlock_commit (kernel/trace/trace.c:1749) [135546.085515] rds_ib_laddr_check(): addr 36.74.25.172 ret -99 node type -1 Acked-by:
Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
-
Jason Wang authored
[ Upstream commit 48900cb6 ] virtio declares support for NETIF_F_FRAGLIST, but assumes that there are at most MAX_SKB_FRAGS + 2 fragments which isn't always true with a fraglist. A longer fraglist in the skb will make the call to skb_to_sgvec overflow the sg array, leading to memory corruption. Drop NETIF_F_FRAGLIST so we only get what we can handle. Cc: Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
Jason Wang <jasowang@redhat.com> Acked-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit d69bbf88 ] Only cpu seeing dst refcount going to 0 can safely dereference dst->flags. Otherwise an other cpu might already have freed the dst. Fixes: 27b75c95 ("net: avoid RCU for NOCACHE dst") Reported-by:
Greg Thelen <gthelen@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 8fa677d2 ] Under low memory conditions, tcp_sk_init() and icmp_sk_init() can both iterate on all possible cpus and call inet_ctl_sock_destroy(), with eventual NULL pointer. Signed-off-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
-
Ani Sinha authored
[ Upstream commit 44f49dd8 ] Fixes the following kernel BUG : BUG: using __this_cpu_add() in preemptible [00000000] code: bash/2758 caller is __this_cpu_preempt_check+0x13/0x15 CPU: 0 PID: 2758 Comm: bash Tainted: P O 3.18.19 #2 ffffffff8170eaca ffff880110d1b788 ffffffff81482b2a 0000000000000000 0000000000000000 ffff880110d1b7b8 ffffffff812010ae ffff880007cab800 ffff88001a060800 ffff88013a899108 ffff880108b84240 ffff880110d1b7c8 Call Trace: [<ffffffff81482b2a>] dump_stack+0x52/0x80 [<ffffffff812010ae>] check_preemption_disabled+0xce/0xe1 [<ffffffff812010d4>] __this_cpu_preempt_check+0x13/0x15 [<ffffffff81419d60>] ipmr_queue_xmit+0x647/0x70c [<ffffffff8141a154>] ip_mr_forward+0x32f/0x34e [<ffffffff8141af76>] ip_mroute_setsockopt+0xe03/0x108c [<ffffffff810553fc>] ? get_parent_ip+0x11/0x42 [<ffffffff810e6974>] ? pollwake+0x4d/0x51 [<ffffffff81058ac0>] ? default_wake_function+0x0/0xf [<ffffffff810553fc>] ? get_parent_ip+0x11/0x42 [<ffffffff810613d9>] ? __wake_up_common+0x45/0x77 [<ffffffff81486ea9>] ? _raw_spin_unlock_irqrestore+0x1d/0x32 [<ffffffff810618bc>] ? __wake_up_sync_key+0x4a/0x53 [<ffffffff8139a519>] ? sock_def_readable+0x71/0x75 [<ffffffff813dd226>] do_ip_setsockopt+0x9d/0xb55 [<ffffffff81429818>] ? unix_seqpacket_sendmsg+0x3f/0x41 [<ffffffff813963fe>] ? sock_sendmsg+0x6d/0x86 [<ffffffff813959d4>] ? sockfd_lookup_light+0x12/0x5d [<ffffffff8139650a>] ? SyS_sendto+0xf3/0x11b [<ffffffff810d5738>] ? new_sync_read+0x82/0xaa [<ffffffff813ddd19>] compat_ip_setsockopt+0x3b/0x99 [<ffffffff813fb24a>] compat_raw_setsockopt+0x11/0x32 [<ffffffff81399052>] compat_sock_common_setsockopt+0x18/0x1f [<ffffffff813c4d05>] compat_SyS_setsockopt+0x1a9/0x1cf [<ffffffff813c4149>] compat_SyS_socketcall+0x180/0x1e3 [<ffffffff81488ea1>] cstar_dispatch+0x7/0x1e Signed-off-by:
Ani Sinha <ani@arista.com> Acked-by:
-
Phil Reid authored
[ Upstream commit e6dbe1eb ] priv->hwts_*_en indicate if timestamping is enabled/disabled at run time. But priv->dma_cap.time_stamp and priv->dma_cap.atime_stamp indicates HW is support for PTPv1/PTPv2. Signed-off-by:
Phil Reid <preid@electromag.com.au> Acked-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
-
Carol L Soto authored
[ Upstream commit c02b0501 ] When doing memcpy/memset of EQEs, we should use sizeof struct mlx4_eqe as the base size and not caps.eqe_size which could be bigger. If caps.eqe_size is bigger than the struct mlx4_eqe then we corrupt data in the master context. When using a 64 byte stride, the memcpy copied over 63 bytes to the slave_eq structure. This resulted in copying over the entire eqe of interest, including its ownership bit -- and also 31 bytes of garbage into the next WQE in the slave EQ -- which did NOT include the ownership bit (and therefore had no impact). However, once the stride is increased to 128, we are overwriting the ownership bits of *three* eqes in the slave_eq struct. This results in an incorrect ownership bit for those eqes, which causes the eq to seem to be full. The issue therefore surfaced only once 128-byte EQEs started being used in SRIOV and (overarchitectures that have 128/256 byte cache-lines such as PPC) - e.g after commit 77507aa2 "net/mlx4_core: Enable CQE/EQE stride support". Fixes: 08ff3235 ('mlx4: 64-byte CQE/EQE support') Signed-off-by:
Carol L Soto <clsoto@linux.vnet.ibm.com> Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
-
Sowmini Varadhan authored
[ Upstream commit 8ce675ff ] Either of pskb_pull() or pskb_trim() may fail under low memory conditions. If rds_tcp_data_recv() ignores such failures, the application will receive corrupted data because the skb has not been correctly carved to the RDS datagram size. Avoid this by handling pskb_pull/pskb_trim failure in the same manner as the skb_clone failure: bail out of rds_tcp_data_recv(), and retry via the deferred call to rds_send_worker() that gets set up on ENOMEM from rds_tcp_read_sock() Signed-off-by:
Sowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by:
-
Guillaume Nault authored
[ Upstream commit 1acea4f6 ] We can't rely on PPPOX_ZOMBIE to decide whether to clear po->pppoe_dev. PPPOX_ZOMBIE can be set by pppoe_disc_rcv() even when po->pppoe_dev is NULL. So we have no guarantee that (sk->sk_state & PPPOX_ZOMBIE) implies (po->pppoe_dev != NULL). Since we're releasing a PPPoE socket, we want to release the pppoe_dev if it exists and reset sk_state to PPPOX_DEAD, no matter the previous value of sk_state. So we can just check for po->pppoe_dev and avoid any assumption on sk->sk_state. Fixes: 2b018d57 ("pppoe: drop PPPOX_ZOMBIEs in pppoe_release") Signed-off-by:
Guillaume Nault <g.nault@alphalink.fr> Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit 50010c20 ] This is decrementing the pointer, instead of the value stored in the pointer. KASan detects it as an out of bounds reference. Reported-by:
"Berry Cheng 程君(成淼)" <chengmiao.cj@alibaba-inc.com> Signed-off-by:
-
- Nov 09, 2015
-
-
Greg Kroah-Hartman authored
-
Greg Kroah-Hartman authored
Fixes the backport of 0b34a166 upstream Commit 0b34a166 "x86/xen: Support kexec/kdump in HVM guests by doing a soft reset" has been added to the 4.2-stable tree" needed to correct the CONFIG variable, as CONFIG_KEXEC_CORE only showed up in 4.3. Reported-by:
Luis Henriques <luis.henriques@canonical.com> Signed-off-by:
-
Doron Tsur authored
commit 0ca81a28 upstream. ib_send_cm_sidr_rep could sometimes erase the node from the sidr (depending on errors in the process). Since ib_send_cm_sidr_rep is called both from cm_sidr_req_handler and cm_destroy_id, cm_id_priv could be either erased from the rb_tree twice or not erased at all. Fixing that by making sure it's erased only once before freeing cm_id_priv. Fixes: a977049d ('[PATCH] IB: Add the kernel CM implementation') Signed-off-by:
Doron Tsur <doront@mellanox.com> Signed-off-by:
Matan Barak <matanb@mellanox.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Dāvis Mosāns authored
commit 22805217 upstream. When pci_pool_alloc fails in mvs_task_prep then task->lldd_task stays NULL but it's later used in mvs_abort_task as slot which is passed to mvs_slot_task_free causing NULL pointer dereference. Just return from mvs_slot_task_free when passed with NULL slot. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=101891 Signed-off-by:
Dāvis Mosāns <davispuh@gmail.com> Reviewed-by:
Tomas Henzl <thenzl@redhat.com> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by:
James Bottomley <JBottomley@Odin.com> Signed-off-by:
-
Jes Sorensen authored
commit 681ab469 upstream. This was introduced with 9e882242 which changed the return value of submit_bio_wait() to return != 0 on error, but didn't update the caller accordingly. Fixes: 9e882242 ("block: Add submit_bio_wait(), remove from md") Reported-by:
Bill Kuzeja <William.Kuzeja@stratus.com> Signed-off-by:
Jes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by:
NeilBrown <neilb@suse.com> Signed-off-by:
-
Jes Sorensen authored
commit 203d27b0 upstream. This was introduced with 9e882242 which changed the return value of submit_bio_wait() to return != 0 on error, but didn't update the caller accordingly. Fixes: 9e882242 ("block: Add submit_bio_wait(), remove from md") Reported-by:
-
Herbert Xu authored
commit 3fc89adb upstream. Currently a number of Crypto API operations may fail when a signal occurs. This causes nasty problems as the caller of those operations are often not in a good position to restart the operation. In fact there is currently no need for those operations to be interrupted by user signals at all. All we need is for them to be killable. This patch replaces the relevant calls of signal_pending with fatal_signal_pending, and wait_for_completion_interruptible with wait_for_completion_killable, respectively. Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Peter Zijlstra authored
commit 275d7d44 upstream. Poma (on the way to another bug) reported an assertion triggering: [<ffffffff81150529>] module_assert_mutex_or_preempt+0x49/0x90 [<ffffffff81150822>] __module_address+0x32/0x150 [<ffffffff81150956>] __module_text_address+0x16/0x70 [<ffffffff81150f19>] symbol_put_addr+0x29/0x40 [<ffffffffa04b77ad>] dvb_frontend_detach+0x7d/0x90 [dvb_core] Laura Abbott <labbott@redhat.com> produced a patch which lead us to inspect symbol_put_addr(). This function has a comment claiming it doesn't need to disable preemption around the module lookup because it holds a reference to the module it wants to find, which therefore cannot go away. This is wrong (and a false optimization too, preempt_disable() is really rather cheap, and I doubt any of this is on uber critical paths, otherwise it would've retained a pointer to the actual module anyway and avoided the second lookup). While its true that the module cannot go away while we hold a reference on it, the data structure we do the lookup in very much _CAN_ change while we do the lookup. Therefore fix the comment and add the required preempt_disable(). Reported-by:
poma <pomidorabelisima@gmail.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by:
-
